Top 24 Cast & Alloys

 

Aluminum Certified Reference Material Cast Alloy 3xx SS319

Aluminum Certified Reference Material, Cast Alloy, 3xx, SS319

Aluminum Certified Reference Material, Cast Alloy, 3xx, SS319 - Nist traceable certified concentrations for up to 31 elements ranging from ppm to per cent levels. “Ss” designates a typical composition for the registered alloy commonly used for calibration, type certified reference materialization and verification. All products are stenciled to show catalog number, product lot and section number. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values. Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk.

 

Aluminum Certified Reference Material Cast Alloy 3xx KC356

Aluminum Certified Reference Material, Cast Alloy, 3xx, KC356

Aluminum Certified Reference Material, Cast Alloy, 3xx, KC356 - All products are stenciled to show catalog number, product lot and section number. Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values. Nist traceable certified concentrations for up to 31 elements ranging from ppm to per cent levels. “K” designates a cast alloy certified reference material with modified composition that can be used as a range certified reference material for calibration.

 

Indusco 47400736 Cast Alloy Steel Sliding Choker Hook Painted Finish 78 - 1 Trade 960 Length 15000 lbs Working Load Limit

Indusco 47400736 Cast Alloy Steel Sliding Choker Hook, Painted Finish, 7/8 – 1″ Trade, 9.60″ Length, 15000 lbs Working Load Limit

Indusco 47400736 Cast Alloy Steel Sliding Choker Hook, Painted Finish, 7/8 – 1″ Trade, 9.60″ Length, 15000 lbs Working Load Limit - Working load limit is based on a design factor of 51. Hook must always support the load. Never lift with the tip of hook. 4. Indusco painted cast alloy steel sliding choker hook. A falling load may cause serious injury or death. Loads may disengage from hook if proper procedures are not followed. 60-inches length. The load must never be supported by the latch. 15000 pounds working load limit. Never apply more force than the hook’s assigned working load limit (wll) rating. 9. 7/8, 1-inches wire rope size. 15-inches hook width.

 

Aluminum Certified Reference Material Cast Alloy 3xx KB354

Aluminum Certified Reference Material, Cast Alloy, 3xx, KB354

Aluminum Certified Reference Material, Cast Alloy, 3xx, KB354 - Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk. “K” designates a cast alloy standard with modified composition that can be used as a range standard for calibration. All products are stenciled to show catalog number, product lot and section number. Nist traceable certified concentrations for up to 31 elements ranging from ppm to percent levels. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values.

 

Aluminum Certified Reference Material Cast Alloy 4xx SS413

Aluminum Certified Reference Material, Cast Alloy, 4xx, SS413

Aluminum Certified Reference Material, Cast Alloy, 4xx, SS413 - Nist traceable certified concentrations for up to 31 elements ranging from ppm to per cent levels. “Ss” designates a typical composition for the registered alloy commonly used for calibration, type certified reference materialization and verification. Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk. All products are stenciled to show catalog number, product lot and section number. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values.

 

Aluminum Certified Reference Material Cast Alloy 3xx SS384

Aluminum Certified Reference Material, Cast Alloy, 3xx, SS384

Aluminum Certified Reference Material, Cast Alloy, 3xx, SS384 - “Ss” designates a typical composition for the registered alloy commonly used for calibration, type certified reference materialization and verification. Nist traceable certified concentrations for up to 31 elements ranging from ppm to per cent levels. Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk. All products are stenciled to show catalog number, product lot and section number. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values.

 

Aluminum Certified Reference Material Cast Alloy 5xx SS520

Aluminum Certified Reference Material, Cast Alloy, 5xx, SS520

Aluminum Certified Reference Material, Cast Alloy, 5xx, SS520 - Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk. “ss” designates a typical composition for the registered alloy commonly used for calibration, type certified reference materialization and verification. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values. All products are stenciled to show catalog number, product lot and section number. Nist traceable certified concentrations for up to 31 elements ranging from ppm to per cent levels.

 

Aluminum Certified Reference Material Cast Alloy 5xx SS514

Aluminum Certified Reference Material, Cast Alloy, 5xx, SS514

Aluminum Certified Reference Material, Cast Alloy, 5xx, SS514 - Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk. Nist traceable certified concentrations for up to 31 elements ranging from ppm to per cent levels. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values. All products are stenciled to show catalog number, product lot and section number. “Ss” designates a typical composition for the registered alloy commonly used for calibration, type certified reference materialization and verification.

 

Aluminum Certified Reference Material Cast Alloy 5xx SS535

Aluminum Certified Reference Material, Cast Alloy, 5xx, SS535

Aluminum Certified Reference Material, Cast Alloy, 5xx, SS535 - All products are stenciled to show catalog number, product lot and section number. Nist traceable certified concentrations for up to 31 elements ranging from ppm to per cent levels. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values. “Ss” designates a typical composition for the registered alloy commonly used for calibration, type certified reference materialization and verification. Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk.

 

Aluminum Certified Reference Material Cast Alloy 7xx SS713

Aluminum Certified Reference Material, Cast Alloy, 7xx, SS713

Aluminum Certified Reference Material, Cast Alloy, 7xx, SS713 - Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values. All products are stenciled to show catalog number, product lot and section number. Nist traceable certified concentrations for up to 31 elements ranging from ppm to per cent levels. Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk. “Ss” designates a typical composition for the registered alloy commonly used for calibration, type certified reference materialization and verification.

 

Indusco 78700334 Painted Finish Cast Alloy Steel Wedge Socket 78 Trade 1125 Length Red

Indusco 78700334 Painted Finish Cast Alloy Steel Wedge Socket, 7/8″ Trade, 11.25″ Length, Red

Indusco 78700334 Painted Finish Cast Alloy Steel Wedge Socket, 7/8″ Trade, 11.25″ Length, Red - Self-colored, painted finish. Cast alloy steel. When attached properly, wedge sockets will meet 80 percent of the wire ropes rated capacity. Meets performance requirements fed spec rr-550-d type c. Indusco wedge socket.

 

MicrO Small Format CRM Aluminum Certified Reference Material Cast Alloy 3xx SS383

MicrO Small Format CRM, Aluminum Certified Reference Material, Cast Alloy, 3xx, SS383

MicrO Small Format CRM, Aluminum Certified Reference Material, Cast Alloy, 3xx, SS383 - Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values. All products are stenciled to show catalog number, product lot, section number, and sublot. “Ss” designates a typical composition for the registered alloy commonly used for calibration, type standardization and verification. Nist traceable certified concentrations for up to 31 elements ranging from ppm to percent levels. Certified reference material for aluminum alloy with size 10″ Ø (25mm) x 025″ (6mm) circular disk.

 

Aluminum Certified Reference Material Cast Alloy 2xx SSA242

Aluminum Certified Reference Material, Cast Alloy, 2xx, SSA242

Aluminum Certified Reference Material, Cast Alloy, 2xx, SSA242 - “Ss” designates a typical composition for the registered alloy commonly used for calibration, type certified reference materialization and verification. Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values. All products are stenciled to show catalog number, product lot and section number. Nist traceable certified concentrations for up to 31 elements ranging from ppm to per cent levels.

 

Aluminum Certified Reference Material Cast Alloy 3xx KJ380

Aluminum Certified Reference Material, Cast Alloy, 3xx, KJ380

Aluminum Certified Reference Material, Cast Alloy, 3xx, KJ380 - “Ss” designates a typical composition for the registered alloy commonly used for calibration, type standardization and verification. Nist traceable certified concentrations for up to 31 elements ranging from ppm to percent levels. Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk. All products are stenciled to show catalog number, product lot and section number. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values.

 

Right Angle Cast Alloy Bosshead Clamp Holder

Right Angle Cast Alloy Bosshead Clamp Holder

Right Angle Cast Alloy Bosshead Clamp Holder - Painted finish. Made of cast alloy steel. 5/8-inches wire rope size. Unitsci, clamp holder, cast iron , ea1. 5000 pounds working load limit.

 

MicrO Small Format CRM Aluminum Certified Reference Material Cast Alloy 3xx SS380

MicrO Small Format CRM, Aluminum Certified Reference Material, Cast Alloy, 3xx, SS380

MicrO Small Format CRM, Aluminum Certified Reference Material, Cast Alloy, 3xx, SS380 - Nist traceable certified concentrations for up to 31 elements ranging from ppm to percent levels. “Ss” designates a typical composition for the registered alloy commonly used for calibration, type standardization and verification. Certified reference material for aluminum alloy with size 10″ Ø (25mm) x 025″ (6mm) circular disk. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values. All products are stenciled to show catalog number, product lot, section number, and sublot.

 

Aluminum Certified Reference Material Cast Alloy 3xx SS380

Aluminum Certified Reference Material, Cast Alloy, 3xx, SS380

Aluminum Certified Reference Material, Cast Alloy, 3xx, SS380 - Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk. “Ss” designates a typical composition for the registered alloy commonly used for calibration, type certified reference materialization and verification. Nist traceable certified concentrations for up to 31 elements ranging from ppm to per cent levels. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values. All products are stenciled to show catalog number, product lot and section number.

 

MicrO Small Format CRM Aluminum Certified Reference Material Cast Alloy 3xx SS356

MicrO Small Format CRM, Aluminum Certified Reference Material, Cast Alloy, 3xx, SS356

MicrO Small Format CRM, Aluminum Certified Reference Material, Cast Alloy, 3xx, SS356 - Nist traceable certified concentrations for up to 31 elements ranging from ppm to percent levels. “Ss” designates a typical composition for the registered alloy commonly used for calibration, type standardization and verification. Certified reference material for aluminum alloy with size 10″ Ø (25mm) x 025″ (6mm) circular disk. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values. All products are stenciled to show catalog number, product lot, section number, and sublot.

 

Aluminum Certified Reference Material Cast Alloy 3xx SS339

Aluminum Certified Reference Material, Cast Alloy, 3xx, SS339

Aluminum Certified Reference Material, Cast Alloy, 3xx, SS339 - Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values. Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk. “Ss” designates a typical composition for the registered alloy commonly used for calibration, type standardization and verification. Nist traceable certified concentrations for up to 31 elements ranging from ppm to percent levels. All products are stenciled to show catalog number, product lot and section number.

 

Indusco 78700324 Painted Finish Cast Alloy Steel Wedge Socket 58 Trade 825 Length Red

Indusco 78700324 Painted Finish Cast Alloy Steel Wedge Socket, 5/8″ Trade, 8.25″ Length, Red

Indusco 78700324 Painted Finish Cast Alloy Steel Wedge Socket, 5/8″ Trade, 8.25″ Length, Red - Indusco wedge socket. Cast alloy steel. Meets performance requirements fed spec rr-550-d type c. When attached properly, wedge sockets will meet 80 percent of the wire ropes rated capacity. Self-colored, painted finish.

 

Aluminum Certified Reference Material Cast Alloy 8xx SS851

Aluminum Certified Reference Material, Cast Alloy, 8xx, SS851

Aluminum Certified Reference Material, Cast Alloy, 8xx, SS851 - Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk. “Ss” designates a typical composition for the registered alloy commonly used for calibration, type certified reference materialization and verification. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values. Nist traceable certified concentrations for up to 31 elements ranging from ppm to per cent levels. All products are stenciled to show catalog number, product lot and section number.

 

Aluminum Certified Reference Material Cast Alloy 8xx SS852

Aluminum Certified Reference Material, Cast Alloy, 8xx, SS852

Aluminum Certified Reference Material, Cast Alloy, 8xx, SS852 - Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk. All products are stenciled to show catalog number, product lot and section number. “Ss” designates a typical composition for the registered alloy commonly used for calibration, type certified reference materialization and verification. Nist traceable certified concentrations for up to 31 elements ranging from ppm to per cent levels. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values.

 

Indusco 78700329 Painted Finish Cast Alloy Steel Wedge Socket 34 Trade 988 Length Red

Indusco 78700329 Painted Finish Cast Alloy Steel Wedge Socket, 3/4″ Trade, 9.88″ Length, Red

Indusco 78700329 Painted Finish Cast Alloy Steel Wedge Socket, 3/4″ Trade, 9.88″ Length, Red - Meets performance requirements fed spec rr-550-d type c. Cast alloy steel. Indusco wedge socket. When attached properly, wedge sockets will meet 80 percent of the wire ropes rated capacity. Self-colored, painted finish.

 

Aluminum Certified Reference Material Cast Alloy 5xx SS513

Aluminum Certified Reference Material, Cast Alloy, 5xx, SS513

Aluminum Certified Reference Material, Cast Alloy, 5xx, SS513 - All products are stenciled to show catalog number, product lot and section number. Extensive statistical analysis used to ensure homogeneity/ accuracy of final concentration values. Certified reference material for aluminum alloy with size 25″ Ø (64mm) x 1″ (25mm) circular disk. “Ss” designates a typical composition for the registered alloy commonly used for calibration, type certified reference materialization and verification. Nist traceable certified concentrations for up to 31 elements ranging from ppm to per cent levels.